2000 Watt Freedom II PMG for Wind Turbines
2000 Watt Freedom II PMG for Wind Turbines

2000 Watt Freedom II PMG

Write a Review
Your Price: $532.99
Part Number: FR-DUAL-PMG
Availability: In Stock.

Choose Options


Freedom II PMG™ Permanent Magnet Generator

with Optional Marine Coating*


Available in 12V & 24V. 48V available for pre-order.

Our Freedom I and Freedom II PMGs are now designed with a keyed shaft and hub stabilizer as well as includes a self-tightening cam-lock washer to prevent the blade set from ever spinning on the shaft. Watch the video below on these great improvements.AAAA


Our Freedom I and Freedom II PMGs now have a smoother and easier rotation! We've designed new technology into our internal parts to get your wind turbine, hydroelectric, and motor mounted Freedom Series PMG to start-up easier and make more power!

Our Freedom II PMG™ permanent magnet generator is specifically designed for wind turbine use and can even be used with vertical axis wind turbines (VAWT).



Operating Information:

  • Produces battery voltage at approximately 266 RPM in parallel; 133 RPM in series
  • Produces twice (2x) the battery voltage at approximately 506 RPM in parallel; 253 RPM in series
  • Produces four times (4x) the battery voltage at approximately 960 RPM in parallel; 480 RPM in series
  • Wiring the output in series is only recommended for extreme high wind conditions.

This permanent magnet generator works best with our set of 9 Raptor Generation 4 Blades and Zinc Plated Hub or our large Falcon 80.5 Inch Diameter 3 Blade and Hub Set.

Not for hydro, gas engine, electric motor coupled use. For wind turbine use only. See our Hydro PMG for these applications.

Why buy a Freedom or Freedom II PMG™ over a Delco car alternator PMA?

The answer is simply more copper! More copper equals more power - each Freedom PMG stator contains twice as much copper than any Delco style PMA.

Additional reasons why the Freedom PMG is better than ANY Delco or other modified car alternator PMA:

  • Some modified alternators use power to make power. Freedom PMGs use no input power.
  • PMAs use a thin aluminum housing and the stator is not pressed in. The Freedom PMG features a very thick aluminum housing and a pressed in stator that helps with proper alignment and durability.
  • PMAs have only two mounting holes. The Freedom PMG has four of them bolted tightly against the mounting bracket for secure mounting.
  • Alternators and some PMAs have a weak rear bearing. The Freedom PMG utilizes two heavy duty bearings.
  • Most car alternators and PMAs that are repurposed use low grade/high iron electrical steel which can create a lot of heat. The Freedom PMG uses high grade electrical steel and is optimized for efficient cooling

Here is what our customers are saying:

"Finally tested one of the dual PMGs 12/24 , [at] 45km wind it put out [at] 1040 watts, [at] 70km wind 2084 watts, real power (ie in the hundreds of watts seems to kick in 25 km and above). Once winds are 27km and above it makes good power and quickly enters into serious power production. So turns out to be quite good."

PMG Features:

  • NO COGGING, easy to turn - CUT-IN SPEED IS 6 MPH
  • Comes with two heavy duty rectifiers & one hub spacer stabilizer
  • Skewed stator core with high grade electrical steel and heavy duty copper windings
  • 17 mm stainless steel shaft compatible with all Missouri Wind and Solar hubs
  • 2x thick polished aluminum case
  • Zinc plated 28 rare earth neodymium magnet rotor
  • For charging 12, 24, or 48 volt battery banks
  • Specifically designed for wind turbines.
  • Fits delco bolt patterns and mounts up to our standard mounting bracket.
  • Comes with two bridge rectifiers

PMG Specifications:

  • 3/8" diameter bolt holes
  • 1 15/16" on center between mounting holes
  • 5 7/8" OD width
  • 6 5/16" tall
  • 9 1/2" overall length
  • Shaft thread & size: M16 - 1.5 (M=metric, 1.5 = metric thread pitch)
*Optional Marine Finish:


Saltwater environments will cause the internal components to rust over time. Our marine varnish service includes disassembling the motor and coating the interior. As our sold-separately PMA Coating can only ship by ground service and is restricted in some countries, Missouri Wind and Solar is offering an add-on service to coat the internal components before shipping. Prolong the life of your Freedom PMG by protecting it from the effects of saltwater environments. Please allow additional handling time when choosing this service.





Make sure you also check out our 14 magnet Freedom PMG™!

Missouri Wind Freedom II PMG Power Curve




Customer Video:

Wind Turbine Testing in Our Wind Tunnel: 

Freedom II Output with the MidNite Classic Charge Controller:


Recently Viewed Items