Free shipping on hundreds of products

Missouri Freedom 3 Nine Blade Wind Turbine

 

Features the superior quality and performance of the All-New Freedom 3 Fully Sealed PMG - with our original Raptor Generation 4 carbon fiber blades!


Freedom 3 Sealed PMG - For Land or Sea

 

Our Missouri Freedom Wind Turbines are hot-dipped galvanized with zinc-plated hubs! Resists Rust - No need for painting or special coating for up to 50 years under normal conditions

Highly Anticipated - All New for 2019, Our Freedom 3 Sealed PMG is Perfect for Marine Use or Anywhere a Wind Turbine Can Be Mounted.


  

The NEW Missouri Wind and Solar Freedom 3 PMG is fully sealed to create a water-resistant motor for wind and hydropower. Truly well thought out with years of R&D behind the production. 

We've had the Freedom 3 PMG installed in a less than ideal location on our roof in Seymour, MO with great results. We have even run it through our wind tunnel test at 55 MPH.

The fully sealed motor is perfect for marine environments but can be used anywhere a wind turbine can be mounted.

Just like the Missouri Wind and Solar Freedom PMGs, the Sealed PMG contains more copper than typical PMAs on the market. What does that mean? More copper equals more power output! Our custom made skewed stator reduces cogging and allows startup in lower wind speeds.

Wind Turbine Features:

  • Fully Sealed 1600 Watt Freedom 3 PMG™
    • 3 phase bridge rectifier for converting to DC output
    • (see below for more specifics)
  • Heavy duty hub spacer/stabilizer with slot to fit keyway
  • PMG mounting bracket and heavy-duty Stars & Stripes wind turbine tail
    • Mounting Bracket fits on 1.5" schedule #40 or #80 pipe (1 7/8" OD) and allows for easy turning
    • Tail fin measures 9 3/4 inches wide x 28 3/4 inches tall
      • Cut from 16 gauge steel
    • Hot dipped galvanized weather resistant finish
  • Comes with 9 Raptor Generation 4 carbon fiber composite blades
    • Aerodynamically tapered blades for maximum output
    • Raptor Generation 4 Blades are Made in the USA
  • Assembled blades and hub make 61 inch swept area
  • Overall assembled length: 37 inches
No slip rings to fail or replace. Simple and effective, the turbine uses a wire tension system which will last a lifetime. The single power transmission cord never twists because the wind never spins the turbine around in the same direction hundreds of times. Typically, the wind only comes from two directions. It has yet to be an issue with any one of the thousands of turbines we have distributed.

Fully Sealed Freedom 3 PMG™ Features: 

  • Larger bearing to withstand wear and abuse

  • Sealed front bearing with additional labyrinth style seal

  • Case with a rough, natural finish which means more surface area to speed cooling and improve output performance

  • Keyed shaft and hub stabilizer that bolts on to the blade hub to prevent slipping and improve safety

  • Hub stabilizer that channels water away from entering through the front of the housing

  • Gasket style seal to keep water from seeping into the case

  • Water resistant design - no marine varnish or painting required

  • Wind tunnel testing up to 55 MPH

Freedom PMG Specifications:

  • 17 mm stainless steel shaft compatible with all Missouri Wind and Solar hubs and blade sets
  • Custom hub spacer/stabilizer with keyway and bolts for attaching to Missouri Wind and Solar blade hubs
  • Zinc plated 14 rare earth neodymium magnet rotor
  • No brushes to fail or replace
  • Large, heavy-duty bearings in front and back
  • Fits delco bolt patterns and mounts up to our standard mounting bracket
  • 3/8" Diameter bolt holes
  • 1 15/16" on center between mounting holes
  • 5 7/8" OD Width
  • 6 5/16" Tall
  • 10 pounds

Warnings:

PMA and PMG cases should not be painted or coated - this prevents heat from leaving the motor and reduces efficiency. If you have an open-faced motor like our Freedom single and dual PMGs, you can marine varnish the interior components.


Freedom 3 Sealed PMG Features   Freedom 3 Sealed PMG Features
Product Diagrams:

Missouri Wind and Solar Basic Setup Diagram

Wind Turbine Specifics
Available Voltage 12 Volts
Available Wattage 1600 Watts
Motor Type Freedom PMG
Blade Series Raptor Generation 4
Blade Length 29 Inches / 73.7 Centimeters
Blade Width (at base) 6 Inches / 15.24 Centimeters
Blade Width (at tip) 1 1/8 Inches / 2.86 Centimeters
Blade Material Carbon Fiber
Blade Quantity 5 Blades
Assembled Diameter 61 Inches / 1.55 Meters
Special Coating Zinc Plated

Write a review

Please login or register to review

1600 Watt 9 Blade Missouri Freedom 3 Sealed Wind Turbine

  • $412.99


Available options


Related Products

Missouri Basic 500 Watt 7 Blade Wind Turbine

Missouri Basic 500 Watt 7 Blade Wind TurbineOur Basic Raptor Wind Turbine for home, business, or rem..

$319.99

3-Phase Wind Turbine Cable High Output 10/3

3-Phase Wind Turbine Cable High Output 10/3Used for all 3-phase systemsAC high output runs to your b..

$1.79

3-Phase Wind Turbine Cable Medium Output 12/3

3-Phase Wind Turbine Cable High Output 12/3 Used for all 3-phase systems Combines two of the Freed..

$1.49

Digital All In One Charge Controller with LED Meter for 3-Phase and DC Systems

Missouri Wind 440 Amp/10,000 Watt Hybrid Wind and Solar Charge Controller Available in 12, 24, and 4..

$309.99

Wind and Solar Charge Controller w/ LED Display & 600 Watt Divert Load

Missouri Wind 12 Volt 440 Amp/10,000 Watt Hybrid Wind and Solar Charge Controller with 600 Watt Dive..

$229.99

Tags: Freedom 3, Raptor, G4, Rebel, Freedom PMG, wind turbine, Freewind, Rebel, marine