9 3/8 Inch Dual Power Submersible Water Heating Element

Can be used direct with batteries, solar panels, hydroelectric generators, as a wind turbine dump diversion load.

You can run high voltage through the element as long as you don't exceed the rated wattage of the element.

For example:

  1. A 600 watt element can handle a 600 watt max solar array output of 150 volts 4 amps
  2. A 300 watt element can handle a max output of 300 watts 200 volt at 1.5 amps.  

As long as your panel('s) voltage exceeds the element voltage rating but does not exceed the max output wattage, you can safely use the element.

DO NOT USE GRID POWER AS IT WILL IMMEDIATELY DESTROY THE ELEMENT!

Can also be used as a solar panel dump load. See our wire and cable section for selecting a power cord for the heater from your wind turbine, hydroelectric generator, solar panels, or battery setup, etc.

  • Fits standard water heaters with a 1" NPT or your own custom heater tank.
  • Stainless steel materials 
  • The surface load of the heating pipe is 2W/cm²
  • Pipe Diameter is 8.0mm

Volts & Wattages:

  • 48 Volt 2000W/1000W model can also be wired for the following voltages
    • 12v 100w/50w
    • 24v 440w/220w
    • 36v 970w/485w

Uses:

  • Livestock water tank deicer (low amp draw means you won't drain your battery as fast). For keeping dog, cat, chicken, and other domestic animals' water from freezing.
  • Standard American water heater element replacement for on or off grid applications
  • Water preheating
  • Campers, Motor homes
  • Emergency hot water
  • Portable commercial, industrial machines and equipment
  • Runs off your car battery for portable hot water anywhere
  • Direct wind and solar applications
  • Concrete mixing trucks
  • Use for DIY solar batch water heaters
  • For heating motor oil, vegetable oil, or most any other oils or liquids
  • and many, many more uses where heat or diversion loads are needed.

Question: How many watts are required to heat one gallon of water up one degree?

Answer: It requires 2.4705 watts for one hour.

DC water heating elements are much safer than 110 volt



   



Heat water directly using a wind turbine generator (with or without a battery bank). Wind turbine generators are used primarily for electricity generation.

The power used can be stored in a battery bank or connected to the main supply using a suitable grid tie inverter. In very strong winds, and/or when the batteries are fully charged a wind turbine may generate more current than the batteries can handle.

Therefore a dump load is often used to divert the extra energy to heat water so it is not wasted and so that the wind turbine does not spin so quickly that it is damaged.
Note: If you have a gas hot water heater you may wish to put an electric unit ahead of it. This way the gas heater is always being fed hot water so it does not turn on as often and for shorter periods of time when it does.

Double Water Heating Element Wiring Diagram

Click to Enlarge

Diversion Load DC Water Heating
Pictured below is a typical 12 Volt water heating element which can be screwed into an immersion heater draincock hole. When used as a diversion (dump) load, such an element is connected to the batteries via a charge regulator. When the regulator detects that the batteries are fully charged, it diverts the generated electricity to the element which heats water.

DC Element Diagram

Click here to read more information about DC water heating elements.

Write a review

Please login or register to review

9 3/8 Inch Dual Power Submersible Water Heating Element

  • $39.98
  • $24.95


Available Options


Related Products

Bulkhead Fitting for DC Water Heating Elements

Bulkhead Fitting for DC Water Heating Elements

Bulkhead Fitting for DC Water Heating ElementsPerfect for use with our DC water heating elements and most DC applicationsProduct Specifications:Materi..

$15.99

Tags: element, DC, water, heat, stock tank