Missouri Freedom II 5 Blade Wind Turbine featuring the superior quality and performance of the Freedom II PMG™ - with our longer 38 inch Raptor G5 Blades!
Our Missouri Freedom II Wind Turbine components are hot dipped galvanized with zinc plated hubs!
Resists rust - No need for painting or special coating for up to 50 years under normal conditions*
Longer 38 inch Raptor G5 black carbon fiber blades self regulate their speed in high winds (also available in a 3 blade model).
Our newest innovation in power generation! Our Freedom II Permanent Magnet Generator™ (PMG) is our highest amp model - Up to 2000 watts of output! NO COGGING - Starts up in just 3 to 4 mph winds - Cut in wind speed of 6 MPH.
Output & Performance:
Why buy a Freedom II PMG™ over a Delco car alternator PMA?
The answer is simply more copper! More copper equals more power - each Freedom PMG rotor contains twice as much copper than any Delco style PMA.
Uses: Battery or battery bank charging, stackable wind turbine grid tie inverters, direct DC water heating elements, direct DC resistive heating, or other applications where 3 phase AC or DC can be used.
Note: If you are replacing a DC output wind turbine with our 3 phase turbine and do not want to change your DC wiring then you can mount the bridge rectifier at the top of the tower for a DC run down.
Wind Turbine Features:
- New Freedom II PMG™ for efficient three phase power generation.
- Two 3 phase bridge rectifiers for converting to DC output.
- Heavy duty hub spacer/stabilizer.
- PMG mounting bracket and heavy duty Stars & Stripes wind turbine tail
- Mounting Bracket fits on 1.5" schedule #40 or #80 pipe.
- Comes with five new Raptor G5 38 Inch black carbon fiber composite blades.
- Aerodynamically tapered blades for maximum output.
- Makes 79" swept area. Overall length from blades to tail is 43"
- NO COGGING, easy to turn - CUT-IN SPEED IS 6 MPH
- Comes with two heavy duty rectifiers & one hub spacer stabilizer
- Skewed stator core with high grade electrical steel and heavy duty copper windings
- 17 mm stainless steel shaft compatible with all Missouri Wind and Solar hubs
- 2x thick polished aluminum case
- Zinc plated 28 rare earth neodymium magnet rotor
- For charging 12, 24, or 48 volt battery banks
- Specifically designed for wind turbines.
- Fits delco bolt patterns and mounts up to our standard mounting bracket.
- 3/8" diameter bolt holes
- 1 15/16" on center between mounting holes
- 5 7/8" OD width
- 6 5/16" tall
- 9 1/2" overall length
Saltwater environments will cause the internal components to rust over time. Our marine varnish service includes disassembling the motor and coating the interior. As our sold-separately PMA Coating can only ship by ground service and is restricted in some countries, Missouri Wind and Solar is offering an add-on service to coat the internal components before shipping. Prolong the life of your Freedom PMG by protecting it from the effects of saltwater environments. Please allow additional handling time when choosing this service.
Freedom II PMG Output:
|Wind Turbine Specifics|
|Available Voltage||12/24 Volts, 24/48 Volts, 48/96 Volts|
|Available Wattage||2000 Watts|
|Blade Series||Raptor Generation 5|
|Blade Length||38 Inch / 96.52 Centimeter|
|Blade Width (at base)||6 Inches / 15.24 Centimeters|
|Blade Width (at tip)||1.2 Inches / 30.48 Millimeters|
2000 Watt Missouri Raptor G5 79 Inch Diameter 5 Blade Freedom Wind Turbine
- Brands Missouri Wind and Solar
- Product Code: RAPTOR38_5B_FREEDOMII
- Availability: In Stock