Missouri Freedom 7 Blade Wind Turbine

Features the superior quality and performance of the Freedom PMG™ - with our original Generation 4 carbon fiber blades!

 

Our Missouri Freedom Wind Turbines are hot dipped galvanized with zinc plated hubs!

Resists Rust

No need for painting or special coating for up to 50 years under normal conditions



Missouri Freedom Galvanized Wind Turbine

 

Low wind speed rated wind turbine for home, business, or remote use with the Freedom Permanent Magnet Generator™ (PMG) - 1600 Watts plus potential power!

Raptor Generation 4 carbon fiber blades self regulate their speed in high winds (also available in 5 and 9 blade models).

Our newest innovation in power generation! 

Freedom Permanent Magnet Generator™ (PMG) - This is our highest amp model - Up to 1600 watts of output!  NO COGGING - Cut in wind speed of 6 MPH





Why buy a Freedom PMG™ over a Delco car alternator PMA?

The answer is simply more copper!  More copper equals more power - each Freedom PMG rotor contains twice as much copper than any Delco style PMA. 

Uses: Battery or battery bank charging, stackable wind turbine grid tie inverters, direct DC water heating elements, direct DC resistive heating, or other applications where 3 phase AC or DC can be used. 

Note: If you are replacing a DC output wind turbine with our 3 phase turbine and do not want to change your DC wiring then you can mount the bridge rectifier at the top of the tower for a DC run down.

Wind Turbine Features:

  • 1600 Watt Freedom PMG™ for efficient three phase power generation.
    • 3 phase bridge rectifier for converting to DC output.
    • (see below for more specifics)
  • Heavy duty hub spacer/stabilizer.
  • PMG mounting bracket and heavy duty Stars & Stripes wind turbine tail
    • Mounting Bracket fits on 1.5" schedule #40 or #80 pipe (1 7/8" OD) and allows for easy turning
    • Tail fin measures 9 3/4 inches wide x 28 3/4 inches tall
      • Cut from 16 gauge steel
    • Hot dipped galvanized weather resistant finish
  • Comes with 7 Generation 4 carbon fiber composite blades
    • Aerodynamically tapered blades for maximum output
    • Raptor Generation 4 Blades are Made in the USA
  • Assembled blades and hub make 61 inch swept area.
  • Overall assembled length: 37 inches
No slip rings to fail or replace. Simple and effective, the turbine uses a wire tension system which will last a lifetime. The single power transmission cord never twists because the wind never spins the turbine around in the same direction hundreds of times. Typically, the wind only comes from two directions. It has yet to be an issue with any one of the thousands of turbines we have distributed.

Freedom PMG™ Features: 

  • Specifically designed for wind turbines
  • NO COGGING - Cut in wind speed of 6 MPH
  • Comes with a heavy duty rectifier & hub spacer stabilizer
  • 17 mm stainless steel shaft - compatible with all Missouri Wind and Solar hubs
  • Polished aluminum case
  • Zinc plated 14 magnet rotor and skewed stator core
  • Fits delco bolt patterns and mounts up to our standard mounting bracket.

Freedom PMG Specifications:

  • 3/8" Diameter bolt holes
  • 1 15/16" on center between mounting holes
  • 5 7/8" OD Width
  • 6 5/16" Tall

Product Diagrams:
Missouri Freedom PMG Power Curve

Missouri Wind and Solar Basic Setup Diagram

Wind Turbine Specifics
Available Voltage 12 Volts, 24 Volts, 48 Volts
Available Wattage 1600 Watts
Blade Material Carbon Fiber
Blade Quantity 7 Blades

Write a review

Please login or register to review

1600 Watt 7 Blade Missouri Freedom Wind Turbine

  • $349.98


Available Options


Related Products

1500 Watt Diversion Dump Load Resistor Bank

1500 Watt Diversion Dump Load Resistor Bank

1500 Watt Diversion Dump Load Resistor BankThis divert load resistor is for use to divert the excess power being generated when your wind turbine gene..

$124.98

Tags: wind turbine, freedom, 7, raptor, PMG, PMA