Missouri Freedom 5 Blade Wind Turbine

Features the superior quality and performance of the Freedom PMG™ - with our original Generation 4 carbon fiber blades!

 

Our Missouri Freedom Wind Turbines are hot dipped galvanized with zinc plated hubs!

Resists Rust

No need for painting or special coating for up to 50 years under normal conditions



Missouri Freedom Galvanized Wind Turbine

 

Low wind speed rated wind turbine for home, business, or remote use with the Freedom Permanent Magnet Generator™ (PMG) - 1600 Watts plus potential power!

Raptor Generation 4 carbon fiber blades self regulate their speed in high winds (also available in 7 and 9 blade models).

Our newest innovation in power generation! 

Freedom Permanent Magnet Generator™ (PMG) - This is our highest amp model - Up to 1600 watts of output!  NO COGGING - Cut in wind speed of 6 MPH


 
 


Why buy a Freedom PMG™ over a Delco car alternator PMA?

The answer is simply more copper!  More copper equals more power - each Freedom PMG rotor contains twice as much copper than any Delco style PMA. 

Uses: Battery or battery bank charging, stackable wind turbine grid tie inverters, direct DC water heating elements, direct DC resistive heating, or other applications where 3 phase AC or DC can be used. 

Note: If you are replacing a DC output wind turbine with our 3 phase turbine and do not want to change your DC wiring then you can mount the bridge rectifier at the top of the tower for a DC run down.

Wind Turbine Features:

  • 1600 Watt Freedom PMG™ for efficient three phase power generation.
    • 3 phase bridge rectifier for converting to DC output.
    • (see below for more specifics)
  • Heavy duty hub spacer/stabilizer
  • PMG mounting bracket and heavy duty Stars & Stripes wind turbine tail
    • Mounting Bracket fits on 1.5" schedule #40 or #80 pipe (1 7/8" OD) and allows for easy turning
    • Tail fin measures 9 3/4 inches wide x 28 3/4 inches tall
      • Cut from 16 gauge steel
    • Hot dipped galvanized weather resistant finish
  • Comes with 5 Generation 4 carbon fiber composite blades
    • Aerodynamically tapered blades for maximum output
    • Raptor Generation 4 Blades are Made in the USA
  • Assembled blades and hub make 61 inch swept area
  • Overall assembled length: 37 inches
No slip rings to fail or replace. Simple and effective, the turbine uses a wire tension system which will last a lifetime. The single power transmission cord never twists because the wind never spins the turbine around in the same direction hundreds of times. Typically, the wind only comes from two directions. It has yet to be an issue with any one of the thousands of turbines we have distributed.

Freedom PMG™ Features: 

  • Specifically designed for wind turbines
  • NO COGGING - Cut in wind speed of 6 MPH
  • Comes with a heavy duty rectifier & hub spacer stabilizer
  • 17 mm stainless steel shaft - compatible with all Missouri Wind and Solar hubs
  • Polished aluminum case
  • Zinc plated 14 magnet rotor and skewed stator core
  • Fits delco bolt patterns and mounts up to our standard mounting bracket.

Freedom PMG Specifications:

  • 3/8" Diameter bolt holes
  • 1 15/16" on center between mounting holes
  • 5 7/8" OD Width
  • 6 5/16" Tall

*Optional Marine Finish:

Saltwater environments will cause the internal components to rust over time.  Our marine varnish service includes disassembling the motor and coating the interior. As our sold-separately PMA Coating can only ship by ground service and is restricted in some countries, Missouri Wind and Solar is offering an add-on service to coat the internal components before shipping.  Prolong the life of your Freedom PMG by protecting it from the effects of saltwater environments.  Please allow additional handling time when choosing this service.


Product Diagrams:
Missouri Freedom PMG Power Curve

Missouri Wind and Solar Basic Setup Diagram

Wind Turbine Specifics
Available Voltage 12 Volts, 24 Volts, 48 Volts
Available Wattage 1600 Watts
Motor Type Freedom PMG
Blade Series Raptor Generation 4
Blade Length 29 Inches / 73.7 Centimeters
Blade Width (at base) 6 Inches / 15.24 Centimeters
Blade Width (at tip) 1 1/8 Inches / 2.86 Centimeters
Blade Material Carbon Fiber
Blade Quantity 5 Blades
Assembled Diameter 61 Inches / 1.55 Meters
Special Coating Zinc Plated, Hot Dipped Galvanized

Write a review

Please login or register to review

1600 Watt 5 Blade Missouri Freedom Wind Turbine

  • $329.98


Available Options

Accessories

Enter desired quantity before clicking Add to Cart button


Related Products

Digital All In One Charge Controller with LED Meter for 3-Phase and DC Systems

Digital All In One Charge Controller with LED Meter for 3-Phase and DC Systems

Missouri Wind 440 Amp/10,000 Watt Hybrid Wind and Solar Charge ControllerAvailable in 12, 24, and 48..

$289.98

Wind and Solar Charge Controller w/ LED Display & 600 Watt Divert Load

Wind and Solar Charge Controller w/ LED Display & 600 Watt Divert Load

Missouri Wind 12 Volt 440 Amp/10,000 Watt Hybrid Wind and Solar Charge Controller with 600 Watt Dive..

$198.95

1500 Watt Diversion Dump Load Resistor Bank

1500 Watt Diversion Dump Load Resistor Bank

1500 Watt Diversion Dump Load Resistor BankThis divert load resistor is for use to divert the excess..

$124.98

Dual Freedom II Wind & Solar Digital All in One Charge Controller with LED Meter

Dual Freedom II Wind & Solar Digital All in One Charge Controller with LED Meter

Missouri Wind Dual Hybrid Wind and Solar Charge Controller Dual Digital All In One Charge Contr..

$399.99

Tags: Raptor, G4, Rebel, Freedom PMG, wind turbine